Here’s a detailed Keri entraguard manual guide for installing the Keri Entraguard Silver access control unit. The Entraguard Silver design is for entry-level telephone entry systems, and its installation follows similar steps to other access control units with a few specifics for this model.
PRE-INSTALLATION PLANNING
Tools Needed
- Phillips screwdriver
- Flathead screwdriver
- Wire strippers
- Crimping tool
- Drill (for wall or post mounting)
- Multi-meter
Review the components
- Keri Entraguard Silver unit
- Power supply (12V DC)
- Communication cables (RS-232, RS-485, or Ethernet if TCP/IP is used)
- Door lock wiring and controller
- Telephone line for communication.
Check installation location
- Place at a convenient height, generally 48 to 54 inches from the ground.
- The unit’s location is near the entry point (door or gate) for easy access and wiring.
MOUNTING THE ENTRAGUARD SILVER UNIT
- Use the mounting template included with the unit to mark the mounting points.
- Drill holes as necessary and insert anchors for stability.
- Mount the unit on a solid surface, ensuring adequate clearance for wiring and communication lines.
POWER AND GROUDING
Power requirements
The Entraguard Silver uses 12V DC for operation.
Connect the positive (+) and negative (-) leads from the power supply to the appropriate terminals on the unit.
Grouding
Ensure the unit is properly grounded to avoid electrical issues. Basically, ground the system according to local electrical codes for safety.
WIRING THE SYSTEM
Door Lock Wiring
If using an electromagnetic lock or electric strike, wire the relay outputs from the Entraguard Silver to the locking mechanism. Besides, use Normally Open (NO) or Normally Closed (NC) contacts based on your lock type. Also, ensure a separate power source for the lock if necessary.
Communication Wiring
Telephone Line: Connect the telephone line to Entraguard Silver’s interface port. This is essential for visitor communication and call functions.
RS-232 or RS-485: For more advanced communication, integrate these connections with a central control panel or access controller. This will provide greater effectiveness in the intercom access control system.
Ethernet Connection (optional): If using TCP/IP communication, connect a CAT5 or CAT6 cable from the unit to your network.
Request-to-Exit (REX): If needed, connect a REX device so that the door or gate automatically unlocks when someone exits the premises.
CONFIGURING THE SYSTEM
TESTING THE UNIT
Phone Line Setup
- Program the telephone numbers of residents or personnel into the system.
- Set the number of rings before the unit answers calls.
User Access
- If integrated with a Keri entraguard manual access control system, add user information such as PIN codes or access cards.
- Program unique access schedules and permissions for users.
Access Control Server (optional)
- If the Entraguard Silver connect to a more extensive access control system, configure it using Keri’s Doors.NET software or other compatible management platforms.
TESTING THE UNIT
Power on the Entraguard Silver and check for any system errors or malfunctions.
Test Telephone Functionality
- Place a call from the unit to a programmed resident or personnel number.
- Verify that the recipient can answer and unlock the door remotely.
Check the Locking Mechanism
- Use the access methods (PIN, card, or remote unlock) to ensure the lock engages and disengages properly.
- Test for proper operation of the REX device, ensuring it unlocks the door when exiting.
Confirm Communication
If using RS-232, RS-485, or Ethernet, confirm that the unit communicates correctly with the access control system or network.
FINALIZING AND SECURING THE INSTALLATION
- Inspect Wiring: Ensure all wiring is secure and there are no exposed connections.
- Install Protective Covering (optional): Depending on the environment, consider installing a weatherproof cover to protect the unit from harsh conditions.
MAINTENANCE AND UPDATES
- The inspection in Entraguard Silver is regular to ensure it is functioning correctly.
- Clean the keypad and other components to prevent dirt or damage.
- Update firmware periodically to keep the system secure and functional with the latest features.
This guide provides the essential steps for installing and configuring a Keri Entraguard manual Silver system. For more advanced integration, such as linking with an access control system, specific wiring and configuration might be required based on the setup of your building or property.
WHAT IS KERI SILVER ENTRAGUARD ?
Keri Entraguard Silver is an entry-level telephone entry system that controls access to buildings, doors or other secure areas. It belongs to the intercom access control system family. It is part of Keri Systems’ Entraguard product line, which provides telephone access control solutions that allow visitors to communicate with residents or authorized staff before entering.
WHY INSTALL KERI ENTRAGUARD WITH DICSAN TECHNOLOGY?
Installing a Keri Entraguard Silver system with Dicsan Technology ensures reliable, cost-effective access control for small to medium-sized properties while benefiting from Dicsan’s expert installation and technical support. As a trusted security solutions provider, Dicsan Technology guarantees seamless integration of the Entraguard Silver into your existing infrastructure, providing secure and convenient telephone-based access for residents and visitors. With professional setup, customization, and ongoing maintenance, Dicsan Technology enhances Entraguard Silver’s functionality, ensuring optimal performance, longevity, and ease of use for your property.
